NodeMCU Kit
- No categories
Arduino Mega 2560 Compatible 16U2 ATmega2560 Development Board
රු5,490.00- ATmega 2560 Chip: MEGA R3 Breadboard is equipped with an ATmega 2560 Chip microcontroller with 54 digital I/O pins and 16 analog input pins, allowing users to connect a variety of sensors, displays, and other peripherals
- Mega 2560 R3 Board: ATmega 2560 With 256KB of flash memory space, it provides powerful performance and diverse I/O options, can handle large-scale programs, and is an ideal choice for projects that require a lot of computing resources.
- Arduino Kit: MEGA R3 comes with a powerful RESET circuit, compatible with Arduino MEGA, while using a 5.5 * 2.1mm DC barrel jack, it is also compatible with a 5.5 * 2.5mm DC barrel jack
- Safety Guarantee: Mega R3 has a resettable fuse that protects your computer’s USB port from short circuits and overcurrent. If more than 500 MA of current is applied to the USB port, the fuse will automatically disconnect
Arduino Pro Mini ATMega328 3.3V Board
රු950.00- Pro Mini Atmega328 3.3V 8Mhz
- It has been programmed for its bootloader, without the user to buy ISP burner for programming, user-friendly.
- This board connects directly to the FTDI Basic Breakout board and supports auto-reset.
- Low-voltage board needs no interfacing circuitry to popular 3.3V devices and modules (GPS, accelerometers, sensors, etc)
Arduino Pro Mini ATMega328 5V Board
රු800.00- Microcontroller: ATmega328
- Board Power Supply: 3.35 -12 V (3.3V model) or 5 – 12 V (5V model)
- Circuit Operating Voltage: 3.3V or 5V (depending on model)
- Digital I/O Pins: 14
- PWM Pins: 6
Arduino UNO Original Development Board
රු2,400.00- ATmega328P chip
- 14 digital I/O pins
- 6 analog input pins,
- a USB connection,
- A Power barrel jack,
- ICSP header and a reset button.
- crystal oscillator, serial communication, voltage regulator
Arduino Uno R3 SMD CH340G Compatible
රු1,150.00- Microcontroller: ATmega328P
- Serial IC : CH340G
- Operating Voltage: 5V
- Input Voltage: 7-12V (recommended 5V)
- Digital I/O Pins: 14 (of which 6 provide PWM output)
- PWM Digital I/O Pins: 6
- Analog Input Pins: 6
D1 Mini NodeMcu 4M Bytes Lua WIFI Internet Of Things Development Board Based ESP8266
රු950.00- Use BRT (Bias Resistor Transistor)
- Easier into flash mode.
- 30% increase in radiating area
- Good stability.
Leonardo Original Development Board
රු1,750.00- ATmega32u4 Microcontroller
- Input Voltage: 7-12V
- 20 Digital I/O Pins
- 7 PWM Channels
- 12 ADCs
- 16MHz Clock Speed
- 32 KB Flash Memory
Mega 2560 PRO MINI 5V (Embed) CH340G ATmega2560-16AU
රු4,250.00This is a low cost and miniature version of the popular Arduino Mega 2560. It is assembled with a genuine Atmel ATmega2560 microcontroller and the low cost CH340G USB-UART interface.
This board is compatible with the Arduino Mega 2560. It has a compact form factor of 38 x 54mm and is an excellent solution for developing projects based on ATmega2560.
The Mega Pro Embed functionalities are identical to the Arduino Mega 2560. Even though it is an Embed board, it is solid stable as the Mega Board. It uses the original chip, and a 16 MHz high-quality quartz resonators is present on the board.
Micro:bit V1.5 BBC Offical Microbit Programmable Learning Development Board
රු5,950.00- Nordic nRF51822 Multi-protocol Bluetooth? 4.0 low energy/2.4GHz RF SoC
- 32-bit ARM Cortex M0 microprocessor (16MHz) 16kB RAM, 256kB Flash
- LED matrix ‘screen’ made up of 25 programmable LEDs Two programmable buttons
- USB Plug (Micro-USB plug) Reset button Status LED
NodeMCU ESP8266 WiFi ESP-12E CH340 IoT Dev Board
රු800.00- 32 KB instruction RAM
- 80 KB user data RAM
- 16 KB ETS system data RAM
- External QSPI flash: up to 16 MB is supported (512 KB to 4 MB typically included)
- IEEE 802.11 b/g/n Wi-Fi
- Integrated TR switch, balun, LNA, power amplifier and matching network
- WEP or WPA/WPA2 authentication, or open networks
- 16 GPIO pins
NodeMCU ESP8266 WiFi ESP-12E CP2101 IoT Dev Board
රු1,000.00- The ESP-12 Lua NodeMCU WIFI Dev Board Internet Of Things with ESP8266 is an all-in-one microcontroller + WiFi platform that is very easy to use to create projects with WiFi and IoT (Internet of Things) applications.
- Built-in Micro-USB, with flash and reset switches, easy to program
- Arduino compatible, works great with the latest Arduino IDE/Mongoose IoT/Micropython
- Data download access to the website: http://www;nodemcu;com
