Arduino
BBC microbit
Raspberry Pi
ESP family
AVRCNC Shield UNO-R3 Board 4xA4988 Driver Kit With Heat Sink For Engraver 3D Printer
Rs 2,990.00
- Uses removable A4988 or DRV8825 compatible stepper drivers.
- The extension board can be used for carving machine, 3 d printer driver expansion board
- GRBL 0.8 compatible. (Open source firmware that runs on an -UNO that turns G-code commands into stepper signals)
- PWM Spindle and direction pins,4-Axis support (X, Y, Z , A-Can duplicate X,Y,Z or do a full 4th axis with custom firmware using pins D12 and D13)
- Compact design. Stepper Motors can be connected with 4 pin molex connectors or soldered in place.
- Please note that this is an unassembled kit and Basic soldering skills are needed.
Out of stock
Version: 3.0
Color: Red
Size(L*W*H): 68 x 53 x 18 mm
Voltage: DC 12~36 V (At the moment only the DRV8825 drivers can handle up to 36V so please consider the operation voltage when powering the board.)
Features:
1. Uses removable A4988 or DRV8825 compatible stepper drivers.
2. The extension board can be used for carving machine, 3 d printer driver expansion board
3. GRBL 0.8 compatible. (Open source firmware that runs on an -UNO that turns G-code commands into stepper signals)
4. PWM Spindle and direction pins,4-Axis support (X, Y, Z , A-Can duplicate X,Y,Z or do a full 4th axis with custom firmware using pins D12 and D13)
5. Compact design. Stepper Motors can be connected with 4 pin molex connectors or soldered in place.
6. Please note that this is an unassembled kit and Basic soldering skills are needed.
A4988 Stepper Motor Driver:
Color: Red
Size(L*W*H): 20 x 15 x 10 mm
Thermal shutdown circuitry: Yes
Crossover-current protection: Yes
Ground fault protection: Yes
Load short-circuit protection: Yes
Compatible logic supply: 3.3V and 5 V
Five selectable step modes: full, 1/2, 1/4, 1/8 and 1/16
Features:
1. Mix with slow current decay modes.
2. Internal UVLO and Low RD5 (On) Output.
3. Automatic current decay mode detection/selection.
4. Synchronous rectification for low power dissipation.
5. Warning: Connecting or disconnecting a stepper motor while the driver is powered can destroy the driver.
Uno R3 Board:
MCU: ATmega328
Clock speed: 16 MHz
USB interface: ATmega16U2
Operating voltage: 5 V
I-I / O pin output current: 40 mA max
3.3 V output current: 150 mA max
Digital I/O pins: 14 (including 6 with PWM capability)
Analog input pins: 6
EEPROM: 1 kB
Static RAM (SRAM): 2 kB
Flash memory: 32 kB
Size(L*W*H): 68 x 53 x 10 mm
Package included:
1 x Uno-R3 Board
4 x A4988 Stepper Motor Driver
4 x Heat Sink
1 x USB Cable
1 x 40-Pin Row Needles
Be the first to review “CNC Shield UNO-R3 Board 4xA4988 Driver Kit With Heat Sink For Engraver 3D Printer”
- All items sold as tested are genuinely tested before dispatch.
- Product(s) which show obvious signs of misuse, damage or weather damage will not be eligible for refund or replacement.
- All items are security marked.
- Please ensure all security markings and stickers are intact or any warranty offered will be void.
- All items are subject to satisfactory inspection of the anti-tamper warranty sticker/seal.
- Any evidence that these aforementioned stickers/seals have been removed or broken will render the item out of warranty and will not be covered under warranty rules.
- If the item becomes faulty within that period a replacement will be issued free of charge upon receipt of the faulty item, back to us, if proved to be faulty upon inspection.
- If the item is not faulty or can be repaired, not to the detriment of the item, then this shall be undertaken rather than direct replacement.
Related products
Learning Kits
Learning Kits
Learning Kits
Learning Kits
Learning Kits
Learning Kits
Reviews
There are no reviews yet.