SIM7000C NB-IoT/eMTC/EDGE/GPRS/GNSS Expansion Board for 4G – Raspberry Pi

Rs 12,500.00

For Raspberry Pi Zero/Zero W/Zero WH/2B/3B/3B+
Support TCP, UDP, PPP, HTTP, FTP, MQTT, SMS, email and other functions
Support GNSS positioning (GPS, GLONASS and Beidou)
Onboard USB interface, can be used to test AT commands, obtain GPS positioning information, etc.
Take the UART control pin to access the main control board such as Arduino/STM32

Out of stock

Raspberry Pi 3 B+ SIM7000C NB-IoT/eMTC/EDGE/GPRS/GNSS Expansion Board 4G Communication

Note: Since the NB-IoT is divided into different frequency bands, the current sales version is the Asian version, and the Asian version is limited to use in Asia. This product does not include the Raspberry Pi module and needs to be purchased separately.

【product description】
The product is a tree with NB-IoT (narrowband Internet of Things), eMTC (Enhanced Machine Class Communication), EDGE (Enhanced Data Rate GSM Evolution), GPRS (General Packet Radio Service) and GNSS (Global Navigation Satellite System) functions. Raspberry pie extension board.
NB-IoT and eMTC are emerging IoT communication technologies based on LTE (4G) evolution. They have the advantages of low power consumption, low cost and wide coverage. They are very suitable for applications such as smart meters, remote control, asset tracking, remote monitoring, Internet of Things applications such as telemedicine, mobile POS terminals and shared bicycles. GSM/GPRS and EDGE are traditional 2G and 2.5G communication technologies that support the use of mobile phone cards for texting and wireless communication applications. So whether you want to try new technologies, make evaluations, or want to support multiple ways of communication and positioning, then I am a good choice.

[Features of the product]

For Raspberry Pi Zero/Zero W/Zero WH/2B/3B/3B+
Support TCP, UDP, PPP, HTTP, FTP, MQTT, SMS, email and other functions
Support GNSS positioning (GPS, GLONASS and Beidou)
Onboard USB interface, can be used to test AT commands, obtain GPS positioning information, etc.
Take the UART control pin to access the main control board such as Arduino/STM32
On-board level shifting circuit, the default is 3.3V operation, can be set to 5V through 0 ohm resistor
Onboard SIM card slot, support for ordinary SIM card and NB-IoT dedicated card
2 LED indicators on the board for easy viewing of module operation status
Support serial port baud rate (300bps ~ 3686400bps)
Support AT command control (3GPP TS 27.007, 27.005 and SIMCOM enhanced AT command set)
Support for SIM Application Toolkit (SAT Class 3, GSM 11.14 Release 98, USAT)
Provide a complete supporting information manual (sample programs such as Raspberry/Arduino/STM32)

[Product communication parameters]

	NB-IoT	eMTC	EDGE	GSM/GPRS
Support band	FDD-LTE B1/B3/B5/B8		GPRS/EDGE 900/1800 MHz
Communication Systems	4G		2.5G	2G
Transmission power	Class 3 (0.25W@LTE)		Class E2 (0.5W@EGSM900) Class E1 (0.4W@DCS1800)	Class 4 (2W@GSM900) Class 1 (1W@DCS1800)
Transmission rate	Uplink ≤66kbps Downstream ≤34kbps	Uplink ≤ 375kbps Downstream ≤300kbps	Uplink ≤236.8kbps Downward ≤236.8kbps	Up ≤ 85.6kbps Downstream ≤85.6kbps
Support SIM card	NB special card (sold separately)	SIM card (sold separately)
Applicable area	Asia (domestic support telecommunications / mobile / Unicom)	Asia (domestic does not support, eMTC deployment)	Most countries and regions (domestic support mobile / Unicom)

[Product GNSS parameters]

receive
- 16 channels
- C/A Code
Sensitivity
- Tracking :-162 dBm (GPS) / -157 dBm (GLONASS) / TBD (Beidou)
- Cold start :-148 dBm
First positioning time
- Cold start:
- Hot start:
Precision
- Accurate positioning:

[Other parameters of the product]

Supply voltage: 5V
Operating voltage: 5V / 3.3V (default is 3.3V)
Sleep mode current: 1.2mA (@DRX=2.56s)
Power saving mode current: 9uA
Working temperature: -40 ° C ~ 85 ° C
Storage temperature: -45 ° C ~ 90 ° C
Product size: 30.2mm x 65mm

Reviews

There are no reviews yet.

Be the first to review “SIM7000C NB-IoT/eMTC/EDGE/GPRS/GNSS Expansion Board for 4G – Raspberry Pi” Cancel reply

If you have simply changed your mind or no longer require the item(s), you must notify us within 30 days from receiving your order.

The item(s) must be in their original unused and unopened packaging and be in a resalable condition for a full refund.

You will need to pay for the cost of returning the item(s) and the item(s) remain your responsibility until we receive them.

Damaged caused during transit must be notified within two days of the delivery.

All items sold as tested are genuinely tested before dispatch.
Product(s) which show obvious signs of misuse, damage or weather damage will not be eligible for refund or replacement.
All items are security marked.
Please ensure all security markings and stickers are intact or any warranty offered will be void.
All items are subject to satisfactory inspection of the anti-tamper warranty sticker/seal.
Any evidence that these aforementioned stickers/seals have been removed or broken will render the item out of warranty and will not be covered under warranty rules.
If the item becomes faulty within that period a replacement will be issued free of charge upon receipt of the faulty item, back to us, if proved to be faulty upon inspection.
If the item is not faulty or can be repaired, not to the detriment of the item, then this shall be undertaken rather than direct replacement.